Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
Everyone will have their private assumption on the subject of Installing A Bathtub.
Mounting a bath tub isn't specifically rocket science, yet it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging task. If the old bathtub is readily accessible, the job can relocate speedily; if you have to open a wall to eliminate the old tub and place the new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need an assistant to leave the old bathtub and embeded in the brand-new one. Make sure you have actually certified on your own for the task as well as are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed job, it is better to take into consideration using one prior to you begin. Opportunities are you might require a specialist plumber to make tube links.
This article will certainly help you set up a brand-new bathtub in your restroom if you have already bought a new tub and also do not need to alter the arrangement of your previous water pipelines.
Your tools as well as material list need to make up the following:
Getting ready for the Setup
First of all, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to stop strain on the tub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of removing the existing taps can be rather problematic due to the restricted gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to going on to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, position the bath tub in the required position. The wood boards are practical in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub until the spirit level checks out level.
To mount taps, fit all-time low of the outermost versatile faucet connector to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the water supply as well as check all joints and also brand-new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as also check the overflow outlet and the normal electrical outlet for leakages.
Lastly, fix the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bath tub ought to wait until the bath tub has actually been made use of at the very least once as this will resolve it right into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end gives a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washing machines are in location in between the faucet and the sink. Safeguard the tap in position with the supplier supplied backnut. When the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap adapters. The former type should be connected to the tap ends first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to split an inflexible seal, triggering the water to penetrate the wall between the bath and the tiling, resulting in problems with dampness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes and cartridges, and are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can split relatively very early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise conveniently readily available on the market. It is recommended to fit the tiles utilizing waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads about How to Install a Bathtub Yourself, I thought sharing that excerpt was important. Do you know another person who is very much interested in the niche? Why not promote it. Many thanks for your time. Come back soon.
Avoid property damage; contact us. Report this page